Ashapura Minechem Ltd

• Ideal for internal & external surfaces.
• Excellent resistance to water
• Does not require curing after application.
• No requirement of primer & reduces paint consumption.
• Superior paint finish, economical & easy to use.

• Remove dust, dirt, and foreign matter. 

• The surface should be free from loose particles, grease and any other foreign materials.
• Remove all foreign and loose materials from the wall surface with help of emery stone, putty blade or wire brush and clean the surface with water. 
• In case of cracks or voids, it should be repaired by application of mix of 3-part Cetcrack and 1-part water/Cetcrete latex.

• Scrub the surface with coarse wire brush/ sand paper and clean thoroughly so that it is free from old paint/dust particles till the cementitious plastered surface is seen.

• If surface plaster is rough, apply 1st Cetplast UC level the surface. Cure the surface for 2 days, before starting putty application. 

• If the surface is very smooth either old or new, scraping the surface with emery stone paper is recommended before putty application.

• Due to salty water or salts in sand/bricks, problem of efflorescence is observed; in that case, plastered surface should be treated with mild acid for 30 min, wash the surface thoroughly after that sono acid remains on the wall. It is highly recommended to use Cetcrete Latex 1 to 2 kg per 20 kg putty along with water.

• Mix Cetcoat SF wall putty and 35-40% of water by volume to stiff consistency manually or by using suitable mixer.
• For 40 kg Cetcoat SF wall putty, 14-16 litres of water are advisable.
• Leave the mixture for 5 to 10 minutes for polymerisation and remix.
• Use within 90 minutes.
• Mix the product in such quantities that it can be used in specific time

• The surface should be moderately rough and in just-wet condition (SSD condition)
• Apply 1st coat of Cetcoat SF wall putty (1.5 mm thickness) using a blade/spatula on the wall with bottom to up direction.
• Apply 2nd coat of Cetcoat wall putty (1 mm thickness) after 4 to 6 hours in other direction.
• Allow complete drying for 3 days and then use fine emery paper to remove application marks, if any.

• Ideal for external surfaces
• Excellent resistance to water
• Does not require curing after application
• No requirement of primer & reduces paint consumption
• Superior paint finish, economical & easy to use.

• Remove dust, dirt, and foreign matter. 

• The surface should be free from loose particles, grease and any other foreign materials.
• Remove all foreign and loose materials from the wall surface with help of emery stone, putty blade or wire brush and clean the surface with water. 
• In case of cracks or voids, it should be repaired by application of mix of 3-part Cetcrack and 1-part water/Cetcrete latex.

• Scrub the surface with coarse wire brush/ sand paper and clean thoroughly so that it is free from old paint/dust particles till the cementitious plastered surface is seen.

• If surface plaster is rough, apply 1st Cetplast UC level the surface. Cure the surface for 2 days, before starting putty application. 

• If the surface is very smooth either old or new, scraping the surface with emery stone paper is recommended before putty application.

• Due to salty water or salts in sand/bricks, problem of efflorescence is observed; in that case, plastered surface should be treated with mild acid for 30 min, wash the surface thoroughly after that sono acid remains on the wall. It is highly recommended to use Cetcrete Latex 2 to 3 kg per 20 kg putty along with water.

• Mix Cetcoat Lotus wall putty and 35-40% of water by volume to stiff consistency manually or by using suitable mixer.
• For 40 kg Cetcoat Lotus wall putty, 14-16 litres of water are advisable.
• Leave the mixture for 5 to 10 minutes for polymerisation and remix.
• Use within 90 minutes.
• Mix the product in such quantities that it can be used in specific time

• The surface should be moderately rough and in just-wet condition (SSD condition)
• Apply 1st coat of Cetcoat Lotus wall putty (1.5 mm thickness) using a blade/spatula on the wall with bottom to up direction.
• Apply 2nd coat of Cetcoat Lotus wall putty (1 mm thickness) after 4 to 6 hours in other direction.
• Allow complete drying for 3 days and then use fine emery paper to remove application marks, if any.

• Ideal for external surfaces
• Excellent resistance to water
• Does not require curing after application
• No requirement of primer & reduces paint consumption
• Superior paint finish, economical & easy to use.

• Remove dust, dirt, and foreign matter. 

• The surface should be free from loose particles, grease and any other foreign materials.
• Remove all foreign and loose materials from the wall surface with help of emery stone, putty blade or wire brush and clean the surface with water. 
• In case of cracks or voids, it should be repaired by application of mix of 3-part Cetcrack and 1-part water/Cetcrete latex.

• Scrub the surface with coarse wire brush/ sand paper and clean thoroughly so that it is free from old paint/dust particles till the cementitious plastered surface is seen.

• If surface plaster is rough, apply 1st Cetplast UC level the surface. Cure the surface for 2 days, before starting putty application. 

• If the surface is very smooth either old or new, scraping the surface with emery stone paper is recommended before putty application.

• Due to salty water or salts in sand/bricks, problem of efflorescence is observed; in that case, plastered surface should be treated with mild acid for 30 min, wash the surface thoroughly after that sono acid remains on the wall. It is highly recommended to use Cetcrete Latex 2 to 3 kg per 20 kg putty along with water.

• Mix Cetcoat Lotus wall putty and 35-40% of water by volume to stiff consistency manually or by using suitable mixer.
• For 40 kg Cetcoat Lotus wall putty, 14-16 litres of water are advisable.
• Leave the mixture for 5 to 10 minutes for polymerisation and remix.
• Use within 90 minutes.
• Mix the product in such quantities that it can be used in specific time

• The surface should be moderately rough and in just-wet condition (SSD condition)
• Apply 1st coat of Cetcoat Lotus wall putty (1.5 mm thickness) using a blade/spatula on the wall with bottom to up direction.
• Apply 2nd coat of Cetcoat Lotus wall putty (1 mm thickness) after 4 to 6 hours in other direction.
• Allow complete drying for 3 days and then use fine emery paper to remove application marks, if any.

Cetcoat HS 1017 Wall Putty is a polymer modified white cement based wall putty, specially developed as ultra-white or colour finishing coat to cover up the major undulations and pinholes to level the surface.

Advantages:

• Ideal for external use & sealing area.
• Save cost of primer & paint.
• Superior matt- finish, economical & easy to use.
• Ideal for internal surfaces only.
• Excellent resistance to water
• Does not require curing after application.

• Remove dust, dirt, and foreign matter from the wall surface with help of emery stone, putty blade or wire brush and clean the surface with water. 
• In case of cracks or voids, it should be repaired by application of mix of 3-part Cetcrack & 1-part water /Cetcrete Latex. 

• Mix Cetcoat HS and 15-16 litres of clean water by volume (38-40%) to stiff consistency manually or by using suitable mixer.
• Leave the mixture for 5 to 10 minutes for polymerisation and re-mix.
• Use within 60 minutes.
• Mix the product in such quantities that it can be used in specific time.

• The surface should be moderately rough and in just-wet condition (SSD condition)
• Apply 1st coat of Cetcoat HS (1.5 mm thickness) using a blade/spatula on the wall with bottom to up direction.
• Apply 2nd coat of Cetcoat HS Wall putty (1 mm thickness) after 4 to 6 hours in other direction. 
• Allow complete drying for 3 days. 
• Don’t use fine emery paper to remove application marks, take care during application to avoid mark.

Cetplast UC is a versatile facing material that can be applied to directly over smooth concrete surface without hacking or undulating surface and can be used as base coat /undercoat for interiors or as final finish for exteriors.

Cetplast UC is polymer modified white cement based specially 2-in-1 thin application Plaster-cum-Wall Putty in 3 to 6 mm thickness in two coat against conventional plater 12 mm plus Putty 1.5 mm

Advantages: 

• Under coat over plaster or directly on concrete surface
• Excellent adhesion with substrate
• Reduce water absorption and crack resistant
• Superior matt finish, durable & easy to use
• Economical 3 to 6 mm thickness against conventional plaster 12 mm
• Does not require curing after application
• Ideal for internal, external wall surface & ceiling.
• Available in light grey & white finish.

• The surface should be free from loose particles, grease and any other foreign materials.
• Remove all foreign and loose materials from the wall surface with help of emery stone, putty blade or wire brush and clean the surface with water.

• Mix 25 kg Cetplast UC and 6 to 6.5 litre of water to stiff consistency by using suitable mixer.
• Leave the mixture for 5 minutes for polymerisation and remix.
• Use within 90 minutes.
• Mix the product in such quantities that it can be used in specific time

• Apply 1st coat of Cetplast UC (3 mm thickness) using a blade/spatula on the wall with bottom to up direction.
• Apply 2nd coat of Cetplast UC (1.5 to 3 mm thickness) after 6 to 8 hours in other direction.
• For better silky finish for interiors wall use 2nd coat Cetcoat SF
• Allow complete drying for 3 days
• Don't use fine emery paper to remove application marks, take care during application to avoid mark.

• Ideal for internal & external surfaces.
• Excellent resistance to water
• Does not require curing after application.
• No requirement of primer & reduces paint consumption.
• Superior paint finish, economical & easy to use.

• Remove dust, dirt, and foreign matter. 

• The surface should be free from loose particles, grease and any other foreign materials.
• Remove all foreign and loose materials from the wall surface with help of emery stone, putty blade or wire brush and clean the surface with water. 
• In case of cracks or voids, it should be repaired by application of mix of 3-part Cetcrack and 1-part water/Cetcrete latex.

• Scrub the surface with coarse wire brush/ sand paper and clean thoroughly so that it is free from old paint/dust particles till the cementitious plastered surface is seen.

• If surface plaster is rough, apply 1st Cetplast UC level the surface. Cure the surface for 2 days, before starting putty application. 

• If the surface is very smooth either old or new, scraping the surface with emery stone paper is recommended before putty application.

• Due to salty water or salts in sand/bricks, problem of efflorescence is observed; in that case, plastered surface should be treated with mild acid for 30 min, wash the surface thoroughly after that sono acid remains on the wall. It is highly recommended to use Cetcrete Latex 1 to 2 kg per 20 kg putty along with water.

• Mix Cetcoat SF wall putty and 35-40% of water by volume to stiff consistency manually or by using suitable mixer.
• For 40 kg Cetcoat SF wall putty, 14-16 litres of water are advisable.
• Leave the mixture for 5 to 10 minutes for polymerisation and remix.
• Use within 90 minutes.
• Mix the product in such quantities that it can be used in specific time

• The surface should be moderately rough and in just-wet condition (SSD condition)
• Apply 1st coat of Cetcoat SF wall putty (1.5 mm thickness) using a blade/spatula on the wall with bottom to up direction.
• Apply 2nd coat of Cetcoat wall putty (1 mm thickness) after 4 to 6 hours in other direction.
• Allow complete drying for 3 days and then use fine emery paper to remove application marks, if any.